load on-off power cycling module solenoid controller

Load On-Off Power Cycling Module

Data Sheet
Wiring Diagram

Similar Solenoid Controller and Driver Products

Pick and Hold Module 
Proportional (PWM) Module
Closed Loop Solenoid Position Control Module
Pick and Drop Module
Load On-Off Power Cycling Module
Dual Proportional Valve Controller
Serially Controlled Solenoid Driver
Solenoid Control System
Related Products
Solenoid Controller Card
Power Supplies
Solenoids

 

Features

  • Low Cost

  • Small Size

  • Low Weight

  • High Efficiency

  • Microcomputer Based

  • Very High Reliability

  • Pulse Width Modulated (PWM)

  • Single Supply, from +9 VDC to +50 VDC

  • High Supply Voltage, +50 VDC

  • High Output Current, 15 Amps Peak, 4 Amps RMS
     
  • Incorporates Flyback (Snubber, Freewheeling) Diode per Output Device
     
  • Available with High Side Drivers
  • RoHS Compliant 

  • QUANTITIES AVAILABLE IN STOCK
 
Typical Applications
  • Solenoids

  • Valves

  • Relays

  • Actuators

  • Voice Coil Actuators

  • DC Motors

  • Hydraulics

  • Electromagnets

  • LEDs

General Specifications

  • Supply Voltage, +9 to +50 VDC

  • Peak Current, 15 Amp

  • Average Current, 4 Amp
 

The Load On-Off Cycling Module is designed to enable the user to cycle the voltage across a solenoid, motor or other devices. The applied peak voltage, duty cycle and the frequency are adjusted using the onboard potentiometers.

There are three onboard adjustment potentiometers.

The first potentiometer adjusts the frequency of actuation. The range of the frequency is from 0.14 through 30 cycles per second. The second potentiometer adjusts the output voltage. The duty cycle of the actuation (ratio of on time to the length of one full cycle) may also be adjusted using the third potentiometer.

It is possible to run multiple modules using the designated master board signal generator.

A DIN-rail mount bracket is available for this product.
This product is RoHS compliant.

Performance Specifications

Parameter

Min

Typical

Max

Units

Supply Voltage

9

 

50

VDC

Peak Current    

15

Amp

Average Current  

 

4

Amp

Cycling Frequency

0.14

 

20

Hz

Operating Temperature 0   50 Deg C

80 VDC version is also available.

Timing Diagram

Mechanical Specifications
Mounting Pattern Four 6-32 Screws, 0.15" Diameter (3.8 mm)
Dimensions 3.00” W, 3.00” D, 0.85” H (76.2 mm, 76.2 mm, 21.5 mm)

Ordering Information
 
Part No. Description Amount
LOC-01 Single-device Load On-Off Cycling Module, +50 VDC Version Click to Get a Quote
LOC-01-HC Single-device Load On-Off Cycling Module, High Current Version Click to Get a Quote
LOC-01-HV Single-device Load On-Off Cycling Module, +80 VDC Version Click to Get a Quote
LOC-03 Single-device Bi-directional Load Cycling Module, +50 VDC Version Click to Get a Quote
LOC-03-HC Single-device Bi-directional Load Cycling Module, High Current Version Click to Get a Quote
LOC-03-HV Single-device Bi-directional Load Cycling Module, +80 VDC Version Click to Get a Quote
SCSD-01 Single-device Serially Controlled Solenoid Driver Click to Get a Quote
SCSD-02 Dual-device Serially Controlled Solenoid Driver Click to Get a Quote
       


Home | Products | Accessories | Knowledge Center | About Us | Terms of Use |Testimonials | Featured Products |Site Map | Videos | Contact Us